Improving UAV LiDAR survey accuracy using Ground Control Points

Posted on March 10, 2020 in , ,

By Gert Riemersma

Developing Quality Control and Quality Assurance with UAV LiDAR surveying

The survey and mapping industry has experienced phenomenal growth with the number of surveys conducted using a UAV LiDAR and photogrammetry continuing to increase. The impact of this disruptive technology is similar to that seen in the 1980’s when GPS was first introduced and applied to high accuracy surveying and positioning. In both cases, Quality Assurance and Quality Control (QA/QC) procedures have lagged behind the curve. It takes a while for users to understand the importance of, adopt and implement a QA/QC methodology applicable to each new technology. Typically QA/QC is implemented after the initial flush of excitement has dissipated and the technology is being used in earnest.

Learning QA/QC lessons from the oil industry

QA\QC is essential to ensure the data delivered to the end customer is as accurate as possible and the level of accuracy can be proven. In the 1980’s oil rigs were positioned without any quality checks resulting in millions of dollars wasted. My father, the chief surveyor for Royal Dutch Shell (1977–1987), gleefully regaled a story of how a competitive oil company positioned and then proceeded to drill for oil very close to Shell’s concession in Borneo. When they found oil, my father proceeded to prove that they had actually positioned their oil rig within Shell’s patch and thanked them for their efforts in finding new oil reserves for Shell. The lack of Quality Control had cost the competitive oil company dearly.

In his time as chief surveyor he insisted that contractors adopted QA/QC methodology. He overcame their objections on the grounds of cost, the need to collect additional data and the extra time required to process results. These objections are now completely eradicated in the oil & gas survey industry. It is now taken as read that you will demonstrate the reliability of the data collected and you have the utmost confidence in it. As a direct result of these QA/QC processes being adopted many opportunities arose with new companies formed and new software developed to cater for the demand.

Routescene committed to Quality Assurance – improving confidence in your results

Routescene has a strong ethos of Quality Assurance. A robust survey and data processing methodology, applying consistent and disciplined procedures. This improves results and enables you to identify any errors early. Drawing on my own foundations in land surveying, my many years of experience working in the offshore industry and my father’s QA/QC mantra. A rigorous QA methodology has been applied across the design and development of the complete Routescene system since it’s inception, it’s launch in 2014 and continued improvements to date.

Ground Control Targets provide independent check of LiDAR survey results

Since day 1 we have always considered how the level of accuracy required will impact flight planning, undertaken real-time QC monitoring during the actual survey, checked the results on-site immediately after each flight and deployed Ground Control Targets to provide an independent check of the results. We advocate that every UAV LiDAR survey has ground control established. Setting Ground Control Points (GCP) helps to demonstrate a certain level of accuracy has been achieved. Also avoids data processing issues and assists with the calibration of the sensors on the drone: all of which improve the confidence in the accuracy of the survey.

Surveying in a Ground Control Point using a RTK GNSS Rover
Surveying in a Ground Control Point using a RTK GNSS Rover, Norfolk, UK

Challenges of UAV LiDAR Ground Control Targets

Unlike photogrammetry, it is very difficult to identify individual features such as the corner point of a building, in a LiDAR point cloud. In an orthophoto the detail is continuous with each pixel joining onto it’s neighbours. In a LiDAR point cloud the points are discrete with a space between each individual point. This poses a real challenge if the feature you require is in between two points. To remedy this and enable calibration and accuracy analysis to be performed. It is typical in LiDAR surveys to select a flat surface and analyze each axis individually, which is mathematically far more robust. However, in practice finding a flat surface in a highly vegetated undulating terrain is a tricky task. The solution… utilize dedicated Ground Control Targets during a LiDAR survey to enable ground control.

At Routescene we have evolved the design of our Ground Control Targets over the years, experimenting with a variety of different designs, materials and methodologies. The resulting Ground Control Points can be easily consumed in our post-processing software, LidarViewer Pro, which automatically generates Quality Assurance Reports. We are the only manufacturer offering Ground Control Targets specifically designed for UAV LiDAR mapping.

Routescene UAV Lidar Ground Control Target
Routescene LiDAR Ground Control Target

Quality Assurance procedures require Ground Control Targets to be deployed

The required accuracy of a topographic survey will be determined prior to commissioning, or undertaking the survey and this will vary depending on the use and possibly the National Standards that the data needs to comply with. Further detail about the importance of accuracy is available in our article here.

Irrespective of how the data is collected and then processed the means by which you QA\QC the data needs to be considered. There are existing standards you can use, notably from ASPRS, who offer numerous Accuracy Standards and guidelines for both photogrammetry and LiDAR. What is common to both these survey techniques is the need to use physical Ground Control Points, dispersed across the survey area, to firstly provide a means to calibrate the sensor and secondly to check that the desired accuracy has been achieved.

We consider the latest trend to use an orthophoto, derived from a UAV photogrammetry survey, to calibrate and control a UAV LiDAR survey to be fundamentally flawed. The gross assumption is that the orthophoto is perfect and this is certainly not the case as it’s position and accuracy is derived from GCP’s. The practice is inconsistent with good survey practice as it introduces additional errors into the QA process. It is prudent to “cut out the middleman”, remove the orthophoto from the process, and directly utilize the original GCPs in the QA process.

Ground Control Point, Caddis Aerial
A Ground Control Point, courtesy of Caddis Aerial, Colorado, USA

Routescene developed UAV LiDAR Ground Control Targets

Routescene’s Ground Control Targets are large discs to be positioned on the ground within your survey area. Placed on known geographical points, called Ground Control Points, the coordinate of each Ground Control Target is established using an accurate and independent survey technique. Typically this will be undertaken using an RTK GNSS Rover using a Virtual Reference Station (VRS). The number of Ground Control Targets to be deployed depends on the size of the survey area: for a 500 x 500m area we recommend 4-8 targets are used for the boresight calibration and as check points.

Distribution of Ground Control Points at recent project at Sand Canyon, Colorado, USA
Distribution of Ground Control Points at recent project at Sand Canyon, Colorado, USA.

Measure accuracy with a high degree of confidence

The Ground Control Targets can be seen in the resulting geo-referenced point cloud so you can directly compare the known coordinate of the physical Target with that visible in the point cloud. The difference between the two coordinates is the error: confirming the level of accuracy achieved in the survey. The benefit of collecting many hundreds of points per square meter during a LiDAR survey can be leveraged in the error analysis to create robust statistics and provide a measure of accuracy with a high degree of confidence. Routescene’s Targets are 60cm in diameter and typically each Target will be hit 200-300 times by the lasers from the LiDAR system.

The Target is plumbed directly on top of the GCP and the height offset between the GCP and the Target recorded. The Z difference between the known Target height and the LiDAR point can then be calculated and used to generate a histogram. The Standard Deviation and the Root Mean Square Error (RMSE) can be computed with confidence given the large number of observations in the sample. A similar process is followed to compute the X and Y errors.

Histogram for Routescene Ground Control Targets

Histogram showing the Z difference between the Ground Control Target’s known height and that derived from the LiDAR point cloud. 0.01m spacing, 250 hits. Sand Canyon project, Colorado, USA.

This error analysis forms the basis of the Quality Assurance Report. We have automated this process by automatically extracting the location of each Target from the point cloud and then comparing the target’s “points” with the imported GCP coordinate.

Routescene LiDAR Ground Control Target v2.0
Routescene LiDAR Ground Control Target v2.0 – used during a fixed wing UAV survey in Germany

Highly retro-reflective targets

Through continuous improvement, based on our own field experience and customer feedback, our LiDAR Ground Control Target design is in it’s third iteration. 60cm in diameter, mounted on a small tripod and covered in a highly retro-reflective material, the Target gives a high-intensity return and is easily identifiable in the resultant point cloud.

Each Target has a bubble level built into the surface so it can be accurately levelled. The Target is raised from the ground using the tripod, again to enable easy identification, so the returns can be automatically extracted from the point cloud.

We have also found the Routescene Ground Control Targets to be robust and wind resistant, meaning that once they are positioned they stay in position. Thus reducing time having to inspect and reposition targets during the survey.

The automatic extraction and analysis is undertaken in LidarViewer Pro using the QA Reporting filter. There are many other filter tools in the software enabling workflow to be streamlined.

Setting up Routescene UAV Lidar Ground Control Target
Routescene LiDAR Ground Control Target v3.0 – deployed during the Sand Canyon UAV survey in Colorado, USA.

Boresight calibration

System calibration, part of the QA process, is used to both estimate the systematic errors in the Routescene LidarPod equipment and to determine the boresight alignment. Routescene’s operational procedures recommend that a boresight alignment is performed during every project. We identified that over time there tends to be slight variations in the boresight alignment parameters, and as such they cannot be assume to be constant. Variations in operational temperature, repositioning of the antenna poles, GNSS/INS Kalman filter alignment all contribute to these slight variations.

Routescene’s Ground Control Targets are used to perform this system calibration. The Targets are positioned in a particular way to determine the roll, pitch and heading misalignment. The UAV overflies the Targets in a specific pattern. In subsequent post-processing the boresight misalignments are computed and applied to the raw point cloud.

Conclusion

Deploying Ground Control Targets on known and accurately coordinated GCPs prior to a UAV LiDAR survey provides the assurance that the survey has been properly executed. The final survey results are more robust and quantifiable. It can be demonstrated that the client specified level of accuracy is achieved. Ground Control Targets can also be used to calibrate the equipment on every project. Again ensuring the best possible accuracy is accomplished. In addition, adopting Ground Control Targets in a survey simplifies post-processing. Therefore enabling any gross errors to be identified early in the processing pipeline and avoiding costly reprocessing.

For excellent UAV LiDAR results you need to undertake Quality Assurance. Routescene provide this as standard. Investing in Ground Control Targets for UAV LiDAR surveys increases the value of your data. Taking that extra time and effort to install Targets and to generate Quality Assurance Reports will improve the quality of and your confidence in the resultant data.

See more details of the Routescene Ground Control Targets

Contact us

 

About the Author

Gert Riemersma Routescene CTO and Founder
Gert Riemersma trained as a land surveyor and worked as a hydrographic surveyor for 20 years before moving to work with LiDAR and developing the Routescene UAV LiDAR solution in 2014. His experience includes working as a navigator on an aeromagnetic survey in 1985, flying 16-hour sorties halfway across the Atlantic in a DC4, with very limited GPS constellation, supplemented with Loran-C, to navigate by. Routescene designs and manufactures the UAV LidarPod and LidarViewer Pro software. Routescene’s customers have used the system all over the world, from Australia to Alaska, across a variety of different projects.

Footnote

Quality Assurance – the process of you demonstrating that the reliability and accuracy of the data you have collected is to the agreed specifications.

Quality Control – the process that an end client will use to inspect and check that the collected data is to the standard as agreed in the specifications.

 

Improving accuracy with Routescene Ground Control Targets